Verpackungsberatung

Die richtige Verpackung ist wichtig, um ein Kunstwerk während des Transports nicht zu beschädigen, und hilft auch, einen guten Eindruck zu machen, wenn ein Kunde die Lieferung entgegennimmt. Hier bieten wir detaillierte Schritt-für-Schritt-Anleitungen für die Verpackung zweidimensionaler (Wand-)Kunst.

Flache oder gerollte Verpackungen?

The first thing to decide when shipping wall art is whether to transport the artwork flat (e.g. a stretched canvas) or rolled. Rolling an artwork for transport involves shipping in a tube, and has some important advantages. Risk of damage is reduced by presenting a smaller surface area for transport, and can be further mitigated by selecting a strong cylinder for the outer packaging. A smaller surface area also means that courier charges are usually substantively lower for rolled artwork. Furthermore, if the artwork does not need to be un-mounted prior to packaging, then the steps involved are generally less complicated with rolled work.

There are, however, important limitations associated with rolling an artwork for transport. Rolling is impossible for any artwork with a rigid support, and is complicated if the artwork would need to be un-mounted before being rolled. Rolling is also generally more physically demanding on an artwork, and is only an option, for example, if paint is absolutely dry – touch / surface dry is not remotely sufficient. Furthermore, (re)mounting an artwork following delivery also introduces risks, and while these risks will generally be born after a purchase is complete, no one wants to leave a dissatisfied client holding damaged work.

Most pieces of artwork that Artifuse ships are flat packaged. We consequently describe flat packaging first, after which we discuss rolling an artwork for transport.

Flachverpackungen für den Transport

Werkzeuge

Es sind nur ein paar Werkzeuge erforderlich, um ein Stück für den Transport zu verpacken, die alle wahrscheinlich in Ihrem örtlichen Hardware-Shop zu finden sind. Während die meisten dieser Tools ziemlich häufig sind, sollten Sie besonders auf die Details einiger achten.

Materialien

Safe delivery of a flat-packaged artwork depends upon the quality of the packaging materials used. The difficulty associated with sourcing these materials can vary substantially between countries. In our experience, you will know you have found a decent provider when they stock all of the items on the list that follows. For reference, we typically source our packaging material from Ratioform in Switzerland. Working from the inside-out, the following materials are useful for flat-packaging artwork.

Methode

The best way to protect a piece of art in transport, like staying warm in the snow, is to use multiple layers. We use four key layers of packaging: an inner skin, an inner box, bubble wrap, and an outer box. Each of these layers is described in turn.

Innere Haut

The inner-most packing layer is a skin of plastic film (pallet wrap). This skin helps to protect the surface of an artwork from rubbing and scratches during transport. To ensure that this layer is effective, it is important that the skin itself does not rub or slip on the surface of the artwork. This is achieved by keeping the wrap tight and straight on the front-facing surface. A useful tip is to start wrapping from the back of a piece, so that joins in the wrapping are away from the front-facing surface (in the cavity left by the stretching frame).

Innenkasten

Our partner couriers require each artwork to be double-boxed for transport as part of our transport insurance. We construct an inner box for each artwork using rigid cardboard pads. What we are aiming for is an inner box, which is folded square along two sides in one dimension (e.g. the height of the artwork), and is pinched along the two sides of the other dimension (e.g. the width of the artwork). How to proceed depends upon the size of the artwork relative to your cardboard pads.

Start by sizing the cardboard panels using the T-square. In the simplest case, it will be possible to cut a rectangle from a single cardboard pad, with one dimension equal to two times the length of one of the sides of your artwork (e.g. width), plus two times its depth, plus a margin of approximately 10cm. The length of the other dimension of the cardboard rectangle should be sized to the length of the other side of your artwork (e.g. height) plus 10cm. The first of these dimensions will be folded around your piece, and the second will be closed by pinching ends together. Ideally it will be possible to fold along the grain of the cardboard corrugation. If that is not possible, then you will need to score the folds to obtain clean corners for the inner box.

Having cut the cardboard to size, lay it on a flat surface, and place your artwork face down in the middle, ensuring that the cardboard extends about 5cm beyond either side of your artwork along one dimension (e.g. height). Fold the ends that extend well beyond either side of your artwork and tape them down where they meet in the middle. The inner box is completed by pinching the remaining open sides together to form a triangle on either end, and taping them shut.

Using the tape gun effectively can take a bit of practice, and the preferred approach differs from person to person. In general, we find the following approach works well. First, increase the tension control of the tape gun as high as is comfortable. This helps to control the length of tape used at any one place. To start taping, extend a bit of tape and position it with your free hand. It is often easiest to extend sufficient tape to pass over the first corner. From there, use the tape gun to play out as much tape as you need. Place the gun end of the tape with care, and use a twisting motion to cut the tape. This process is easiest with high quality tape, which tends to tear less and adhere better than cheaper variants.

Luftpolsterfolie

We typically use a single layer of bubble wrap to cover the entire inner box, with a double layer of wrap along two of its sides. As described above, the inner box is completed by pinching ends to form a triangle along two sides. The triangular forms are useful because they provide shock absorption. The folded sides of the inner box are not similarly protected, and it is consequently here that we provide additional protection using bubble wrap.

Start by taping the free end of the bubble wrap square to the inner box, so that its side extends about 10cm beyond the box and its end will wrap around a side that has been pinched to a triangle. Keeping the bubble wrap tight, wrap entirely around the box, cut and tape down to create a single layer. Depending upon the size of your piece, you may need multiple passes to cover the full surface. This should give you a fully covered piece with two open ends, similar to what you had with the inner box, but this time with the open ends of the bubble wrap along the folded ends of the inner box. You can then use the 10cm extension of bubble wrap on either side of the inner box to provide a double layer of padding by taping this down.

Außenkasten

The most common source of damage to the edges of an artwork during transport is sliding about inside the outer box. With luck, your bubble wrapped artwork will fit snugly into a pre-fabricated outer box. If it does not, then the best option is usually to fill any excess space with bubble wrap. Do not use any type of granular filler (e.g. foam balls), which can shift during transport and expose your work to damage.

Once you are happy that your artwork is snugly packaged inside its outer box, you can close the box and tape it shut. We typically tape all exposed seams of the outer box.